INSTALLATION AND SERVICE FOR TELESCOPING​

This precision of our products can be very long-lasting due to necessary maintenance. Therefore, installation and service instructions must be read carefully. Skid protection telescopes sensitive parts of your machine; powder, sawdust, liquid and preserve the objects that could fall. As this protection systems are designed specifically to your machine; assembly and disassembly stage of labor, maintenance, time spent for material change and cleaning, and therefore, the cost of job losses will be reduced radically.

Kozanlı as Engineering, developing engineering solutions for different needs, it will increase the machine's precision processing. All you need spare parts or if the telescope is enough to give you the label number.

Warning​:
 

Walk on the dangerous and harmful to the telescopes telescope sensitivity.

If walking is not marked with warning on Never try telescope.

While stationary machine only if the operator can walk carefully walkable mark. The telescope is designed by the design team taking into account the optimal loads.

Before Assembly
 

      •   You may need skid extensions depending on agriculture in the telescope assembly.
      •   Brass, plastic or deep note of the contact surface is flat and smooth, but also must move hardened steel rollers surface.
      •   Do not place the telescope sled full withdrawal from other tapes; It may be damaged due to bending strain tapes.
      •   Make sure your mounting surface perpendicular to the surface of the slide.
      •   With the heavy lift crane hanging telescopes public transport.
      •   Take measures to prevent damage to the device during the lifting and telescope.
      •   Carefully place the bottom and side guides.
      •   Mounting holes, if necessary, be changed to suit.
      •   Tighten all mounting bolts securely.
 

ASSEMBLY
 

      •   After the completion of manufacture of the telescope, over packaged in plastic foil sprayed anti-corrosion spray and shipped by courier.
      •   Each cassette with a mineral oil to extend the service life of the telescope must be oiled before installing.
      •   It is seated on the rails of the telescope and make sure the appropriate link in the table; Check for shock machine parts and run in for a while to get used to low speed without swagger.
      •   Increase your speed gradually and reach maximum speed. Scrapers may interest first and make a lot of noise because of the hardness uneven progress. These effects are normal and will go away in irregular time slowly. Scissors or sliding parts in low-speed movement will symmetrical. If increasing the speed can not be obtained in this symmetrical movement, a powerful blow to the telescope movement, abnormal fatigue and itching may occur. In this case the operation must be stopped, the movement must be detected and the cause of the problem to be remedied.

Maintenance and Service
 

Visual inspection and cleaning:
 

Maintenance of the telescope is not difficult. Depending on the amount of pollution and work intensity is necessary to clean to extend the life of the telescope. 40 m / min speed in the moving telescope at weekly intervals, visual inspection and cleaning should be done. The cause of the damage and must be replaced to prevent further damage if the damaged part of the system should be investigated. All the parts should be thoroughly cleaned opened. Then thoroughly lubricate with oil glands. It prevents corrosion and facilitates movement. Do not clean with compressed air. The ideal would be more beneficial for a cleaning to completely remove. Check whether the strain in muscles. If damaged parts fell onto a telescope; bent surface must be repaired without causing greater damage.

Periodic maintenance:
 

Telescopes can negatively affect the environment. Therefore, scrapers, scissors, and they stop should be checked and replaced if necessary routine maintenance. Periodic maintenance needed materials (stripper, scissors, etc.) from our company can teminedil such as spare parts, technical service can also be requested for a change.

Emergency Care :

Scrapers damaged due to the coolant or chips, sawdust between bands It should be changed to penetrate. Any problems, excessive noise or disruption in the event of more damage, does not occur immediately so the problem should be resolved. The proposed frequency of maintenance machine suitable for normal use. Maintenance should be performed more often in harsh conditions. In case of damage to the hair falling to pieces because there must be emergency care.

Changing the Wipers:
 

      •   Identify damaged scrapers remove the telescope in place.
      •   Remove the screw connection scraper scrapers dismantle the screws. The welded body and wick scraper or chisel hammers, scrapers remove stale. Be careful not to damage the box (source point of rupture or removable).
      •   If you need to boil back to the originating point, that clears that point, the structure of the source and correct the box.
      •   Insert the new wipers. The length of the standard stripper is 720 mm (imported wipers can be of different sizes). Therefore multiple required for each box. At the end of the wells, even in the midst even sure not to use short pieces. Correct pieces from the corners in an appropriate manner.
      •   The hair on the protection of the scrapers (galvanized or CrNi) Make sure it is installed properly and tighten the bolt.
      •   The bolts should be no space in the best way sitting up, moving on, otherwise the hair will be continued and will cause deformation. Also good tightening of the bolt will cause the dissolution unwind during operation. This will create a very dangerous consequences.